Published on: March 2026 2026
PLANNING, ANALYSIS AND DESIGN OF MUSEUM BUILDING USING STAAD PRO
DINESHKUMAR M
PAVALAN V
Article Status
Available Documents
Abstract
The project is about the planning and design of a museum building at Mannampanthal, Mayiladuthurai, Nagai district with framed structure. The museum building is planned with two floors. Each floor is having a large hall, a common staircase, common bath rooms and toilets were planned. The following features such as a ticket counter, restroom, office, power room, bathroom was also planned. The building design was done as per code IS 456 - 2000 and SP 16. The project is proposed to be built at Mannampanthal, Mayiladuthurai, Nagai district. Themuseum building was analysed using Stadd- pro software and also 3Dimensional drawing elevation was rendered using Revit software
How to Cite this Paper
M, D. (2026). Planning, Analysis and Design of Museum Building using Staad Pro. International Journal of Creative and Open Research in Engineering and Management, <i>02</i>(03). https://doi.org/10.55041/ijcope.v2i3.099
M, DINESHKUMAR. "Planning, Analysis and Design of Museum Building using Staad Pro." International Journal of Creative and Open Research in Engineering and Management, vol. 02, no. 03, 2026, pp. . doi:https://doi.org/10.55041/ijcope.v2i3.099.
M, DINESHKUMAR. "Planning, Analysis and Design of Museum Building using Staad Pro." International Journal of Creative and Open Research in Engineering and Management 02, no. 03 (2026). https://doi.org/https://doi.org/10.55041/ijcope.v2i3.099.
Search & Index
References
1] J. Mohan, C. Selin Ravikumar, and T. S. Thandavamoorthy, “Using STAAD Pro: Building design and analysis,” Journal of Science & Technology, vol. 5, no. 2, pp. 45–50, 2017.[2] S. Srivastav and D. P. Singh, “Dynamic analysis of RC building with comparison between shear wall and bracing system using STAAD Pro software,” Journal of Scientific Research and Technology, vol. 3, no. 4, pp. 17–23, 2025.
[3] K. Wailkar, P. Chide, M. Shende, J. Ralekar, D. Walke, and A. Kurzekar, “Analysis and design of a residential building by using STAAD Pro,” International Journal of Modern Agriculture, vol. 10, no. 2, pp. 1200–1207, 2021.
[4] A. Pandey, A. Chaturvedi, and P. K. Nirmal, “Static and dynamic analysis using STAAD Pro,” International Journal of Scientific Research in Civil Engineering, vol. 5, no. 1, pp. 50–55, 2024.
[5] S. S. Bhavikatti, Design of Reinforced Concrete Structures, 6th ed. New Delhi, India: I. K. International Publishing House, 2018.
[6] B. C. Punmia, A. K. Jain, and A. K. Jain, Theory of Structures, 16th ed. New Delhi, India: Laxmi Publications, 2017.
[7] A. Kumar, A. Gautam, A. Kashyap, and A. Kumar, “Analysis and design of multistorey building using STAAD Pro,” in Proc. Int. Conf. Civil Engineering and Structural Design, 2025, pp. 1–6.
Ethical Compliance & Review Process
- •All submissions are screened under plagiarism detection.
- •Review follows editorial policy.
- •Authors retain copyright.
- •Peer Review Type: Double-Blind Peer Review
- •Published on: Mar 20 2026
This article is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License. You are free to share and adapt this work for non-commercial purposes with proper attribution.