Published on: October 2026
DESIGN AND ANALYSIS OF 3D PRINTED PARTS DEVELOPED THROUGH NANO COMPOSITE MATERIAL AND COMPARATIVE ANALYSIS WITH BASE MATERIAL
Vicky Baelmare Tushar Rahangdale Aditya Kapse Rahul Thombare Vishal Rokade
Prof Ritesh Banpurkar
Nagpur, India
Article Status
Available Documents
Abstract
How to Cite this Paper
Baelmare, V., Rahangdale, T., Kapse, A., Thombare, R. & Rokade, V. (2026). Design and Analysis of 3D Printed Parts Developed Through Nano Composite Material and Comparative Analysis with Base Material. International Journal of Creative and Open Research in Engineering and Management, <i>02</i>(10), 1-9. https://doi.org/10.55041/ijcope.v2i10.007
Baelmare, Vicky, et al.. "Design and Analysis of 3D Printed Parts Developed Through Nano Composite Material and Comparative Analysis with Base Material." International Journal of Creative and Open Research in Engineering and Management, vol. 02, no. 10, 2026, pp. 1-9. doi:https://doi.org/10.55041/ijcope.v2i10.007.
Baelmare, Vicky,Tushar Rahangdale,Aditya Kapse,Rahul Thombare, and Vishal Rokade. "Design and Analysis of 3D Printed Parts Developed Through Nano Composite Material and Comparative Analysis with Base Material." International Journal of Creative and Open Research in Engineering and Management 02, no. 10 (2026): 1-9. https://doi.org/https://doi.org/10.55041/ijcope.v2i10.007.
Search & Index
References
- Gibson, D. Rosen, and B. Stucker, Additive Manufactur-ing Technologies: 3D Printing, Rapid Prototyping, and Di-rect Digital Manufacturing, 3rd ed. New York: Springer, 2021.
- ASTM International, ASTM D638-14: Standard Test Method for Tensile Properties of Plastics, West Con-shohocken, PA: ASTM International,
- [3] ASTM International, ASTM D790-17: Standard Test Meth-ods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials, West Con-shohocken, PA: ASTM International, 2017.
- Ning, W. Cong, J. Qiu, J. Wei, and S. Wang, “Addi-tive manufacturing of carbon fiber reinforced thermoplastic composites using fused deposition modeling,” Composites Part B: Engineering, vol. 80, pp. 369–378, 2015.
- Ferreira, F. Machado, and M. A. Alves, “Evaluation of the mechanical properties of short carbon fiber-reinforced PLA produced by FDM,” The International Journal of Advanced Manufacturing Technology, vol. 93, no. 5, pp. 2487–2499,
- 2017.
- L. Shofner, K. Lozano, F. J. Rodr´ıguez-Mac´ıas, and E. V. Barrera, “Nanofiber-reinforced polymers prepared by fused deposition modeling,” Journal of Applied Polymer Science, vol. 89, no. 11, pp. 3081–3090, 2003.
- Wang, M. Jiang, Z. Zhou, J. Gou, and D. Hui, “3D print-ing of polymer matrix composites: A review and prospec-tive,” Composites Part B: Engineering, vol. 110, pp. 442–458, 2017.
- Li, Y. Li, and S. Liu, “Rapid prototyping of continuous carbon fiber reinforced polylactic acid composites by 3D printing,” Journal of Materials Processing Technology, vol. 238, pp. 218–225, 2016.
- Brenken, E. Barocio, A. Favaloro, V. Krogtd, and R. B. Pipes, “Fused filament fabrication of fiber-reinforced poly-mers: A review,” Additive Manufacturing, vol. 21, pp. 1–16, 2018.
- Somireddy and A. Czekanski, “Mechanical characteri-zation of fused deposition modeling parts,” Journal of Man-ufacturing Science and Engineering, vol. 139, no. 10, p. 101004, 2017.
Ethical Compliance & Review Process
- •All submissions are screened under plagiarism detection.
- •Review follows editorial policy.
- •Authors retain copyright.
- •Peer Review Type: Double-Blind Peer Review
- •Published on: Oct 05 2026
This article is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License. You are free to share and adapt this work for non-commercial purposes with proper attribution.